Okaloosa County BOCC — February 28, 2017 — 2 Final Clean Copy Inland (existing Carts) 2-23-17 (with Asset Management Revisions)(signed) — reading text

property or becomes otherwise unserviceable. • Lids must be watertight, prohibit vectors from entering, and odor emission from exiting. • The lid must be one-piece construction and securely attached to the rear of the wheeled section of the Roll Cart using a rustproof, weather-resistant fastener system. • The lid must be hinged to open by gravity to a position of 270 degrees from the closed position and hang open without stressing the lid, body, or tipping over the Roll Cart. • Lids must be designed to be easily removed in the event of damage or failure. Lid latches are unacceptable. Handle • Each Roll Cart must have a horizontal handle(s) to provide comfortable gripping areas for pushing or pulling the Roll Cart. • The handle shall be integrally molded into the body or lid, and only plastic surfaces shall be exposed to the hands of the user. Wheels/Axle • Roll Carts must be equipped with two (2) plastic molded or rubber wheels making the cart capable of being easily moved and maneuvered. • Wheels shall be snap-on or attached in a way that prevents unintended detachment. • Wheels must be a minimum of 10 inches in diameter for large and medium Roll Carts and a minimum of 8 inches in diameter for small Roll Carts. • Each Roll Cart shall be furnished with a minimum 5/8 inch diameter axle with a corrosion-resistant coating that must be securely attached to the body by molded axle retainers. • The wheels and axle must be rated to meet and exceed load requirements of 3.5 pounds per gallon. Stability • Roll Carts must be stable and self-balancing when in the upright position, whether loaded or empty, and maintain stability when returned to the ground at the end of the dumping cycle. • Roll Carts must be able to remain stable and upright in winds up to 30 miles per hour when empty. Color • Color must not be streaked in the finished product and must be colorfast so that the color does not alter significantly with normal use. Painted Roll Carts are unacceptable. • The Solid Waste Roll Cart and lid shall be a color specified by the County with black wheels. • The Recycling Roll Cart and lid shall be a color specified by the County with black wheels. • The final color section must be approved by the County prior to manufacturing. Page 44 Okaloosa County Solid Waste and Recyclables Collection, Transfer, and Processing/Disposal Agreement (using existing bins) Markings • Sequential serial numbers must be molded, branded, or hot stamped into the front of the body with white color. • An eight to ten (8-10) alpha/numeric serial number shall be used as determined by the County. • A Okaloosa County logo and Recycling logo must be clearly molded, inscribed, or hot-stamped into both sides of the body with the following working in 1 inch lettering on the lid: o Property of Okaloosa County. o Instructions for which side of the Roll Cart must face the street for collection. o Recycling Roll Cart lids must include program instructions as determined by the County. o Any other ANSI and regulatory labeling required. • The County must approve all markings prior to the manufacturing of the Roll Carts. Warranty • Roll Carts must be fully (100%) warranted against defects in materials and workmanship for a minimum period of ten (10) years from the date of delivery and be transferrable to the County at the expiration of this Agreement. • The warranty must be unconditional and non-prorated providing the County with assurance of full Roll Cart replacement. The warranty must survive the termination of any contract for the manufacture and/or assembly and distribution of the Roll Carts. • Warranty is understood to include the following coverage: o Failure of the lid to prevent rainwater from entering the Roll Cart when the lid is closed on the body. o Damage to the body, the lid, or any component parts through opening or closing the lid. o Failure of the lid hinge to remain fully functional and continually hold lid in the originally-designed and intended positions when either opened or closed. o Failure of the body and lid to maintain its original shape. o Wear through of Roll Cart bottom so that it leaks liquid. o Failure of the wheels to provide continuous, easy mobility, as originally designed. o Failure of any part to conform to minimum standards as specified. Page 45