Fort Walton Beach Council agenda — 04-26-11 regular — reading text

Accelerating the vehicle fully, until reaching the approximate speed of 45 mph on rough pavement. Evidence of the actual testing techniques shall be made available upon request. Meets Exceeds Comments: 188. COMPARTMENTATION L The customer wishes to take full advantage of as much compartmentation area as possible; Ld this includes underbody pull -out compartmentation for cribbing and airbags. Proposals shall a provide great detail regarding the number, width, height, location, adjustable shelving, and J construction materials, methods, and finishes for each body storage compartment. This shall M include storage areas for ladders, pikepoles, and other relevant equipment. All compartments O r shall have permanent "rope style" perimeter lighting so that the entire compartment may be visible in low light conditions. a Meets Exceeds Comments: L 3 189. ADJUSTABLE SHELVES a There shall be adjustable shelves, with a minimum capacity of 500 pounds provided. Each shelf shall be painted Spatter Gray as standard. Each shelf shall be infinitely adjustable by 00MN means of a threaded fastener, which slides in a track. The shelves shall be held in place by 12" thick stamped plated brackets and bolts. Proposals shall provide details on the S U_ location, number, and construction of all shelving. 4 Vd CL Meets Exceeds Comments: U) Y V L 190. COMPARTMENT DOORS L d Unpainted roll -up style doors shall be used for all storage compartments, except those that are restricted in height, width, or depth and the use of swinging hinged doors is more practical. All Jo compartment doors shall have a switch that warns the driver when the apparatus is placed in gear with a compartment door open. Proposals shall be detailed and clearly identify the type, d E brand, and construction of all compartment doors utilized on the apparatus. The latching and L locking mechanism for all compartment doors shall also be detailed in the UR a manufacturer' s proposal and the warranty limits for each style door and latching mechanism shall be noted. Meets Exceeds Comments: 191. PULL -OUT TRAYS The customer wishes to make full use of pull -out compartment trays where possible. The trays shall have a minimum load capacity of 500 lbs. in the extended position. Page 56 of 93 Slides shall be ball bearing type for ease of operation and years of dependable service. Proposals shall provide significant details on the number, location, and construction of all pull -out trays on the apparatus. Meets Exceeds Comments: 192. SWING OUT TOOLBOARD A swing out aluminum toolboard shall be provided. It shall be a minimum of .188" thick with . 20" diameter holes in a pegboard pattern with 1. 00" centers between holes. The board shall be mounted on a pivoting device at the front of the compartment on the top and bottom to allow easy movement in and out of the compartment. The maximum tool load shall be 400 pounds. The board shall have positive lock in the stowed and extended position. d The board shall be mounted on adjustable tracks from front to back within the compartment J There shall be a minimum of One ( 1) toolboard provided and it shall be finished to match M r compartment interior. 0 Proposals shall provide details regarding the toolboard( s), its location, operation, a LL construction, and use. Meets Exceeds Comments: 3 a 00M 193. BACKBOARD STORAGE N r Mounting shall be provided for at least one ( 1) backboard located in the area of the crosslays. The board( s) shall be enclosed and removable from either side of the vehicle. Meets Exceeds Comments: 194. REAR BUMPER A stainless steel rear bumper is desired. Bumper shall be highly polished, has radiused ends and reinforcing ribs top and bottom. It shall extend the full width of the body. A 4. 00" formed steel channel shall be mounted directly behind the bumper for additional strength. Meets Exceeds Comments: 195. RUB RAIL Bottom edge of the side compartments shall be trimmed with a bright aluminum extruded rub rail. Trim shall be approximately 3. 12" high with 1. 50" flanges turned outward for rigidity. The rub rails shall not be an integral part of the body construction, which allows replacement in the event of damage. Meets Exceeds Comments: Page 57 of 93 195. BODY FENDER CROWNS Polished stainless steel fender crowns shall be provided around the rear wheel openings. An unpainted fender liner shall be provided to avoid paint chipping. The liners shall be removable to aid in the maintenance of rear suspension components. A dielectric barrier shall be provided between the fender crown fasteners ( screws) and the fender sheet metal to prevent corrosion. The fender crowns shall be held in place with stainless steel screws that thread directly into a composite nut and not directly into the parent body sheet metal to eliminate dissimilar metals contact and greatly reduce the chance for corrosion. Meets Exceeds Comments: 196. HANDRAILS Handrails shall be located on the front of the body in positions needed to meet NFPA requirements. Jv Meets Exceeds Comments: 0 r 197. AIR BOTTLE STORAGE a A total of four (4) air bottle compartments shall be provided and located ( 2) on the Passenger side body fender panel ( 2) on the Driver Side rear body fender panel. A stainless steel door with a chrome plated latch shall be provided to contain the air bottle. A dielectric barrier shall 3 be provided between the door hinge, hinge fasteners and the body sheet metal. a Meets Exceeds Comments: M co N n 198. LADDERS 1. There shall be one ( 1) 35', two ( 2) section, aluminum extension ladder provided 2. There shall be one ( 1) 24', two ( 2) section, aluminum extension ladder provided. 3. There shall be a 16' aluminum roof ladder provided. 4. There shall be one ( 1) 14' roof, aluminum ladder provided and mounted on the aerial 5. There shall be one ( 1) 10' aluminum folding ladder(s) provided. 6. There shall be one model 17 Little Giant aluminum folding ladder provided. All ladders must have permanent storage positions on the vehicle. Meets Exceeds Comments: 199. GROUND LADDER STORAGE Ladder tunnels shall be provided at the rear of the apparatus. Tunnels shall be capable of holding all ladders, unless otherwise noted or agreed to by the customer. The ladders shall be held captive top and bottom by aluminum tracks and slide on friction reducing material. Page 58 of 93 All ladders shall be removable individually without having to remove any other ladder. A quick release device shall keep the ladders secured in the storage area. Meets Exceeds Comments: 200. PIKE POLES 1. There shall be one ( 1) 12 foot pike pole with fiberglass I - beam handle provided. The pike pole shall be stored in tubular holders located in the ground ladder storage compartment area. 2. There shall be one ( 1) 8 foot pike pole with fiberglass I beam handle provided. The pike pole shall be stored in tubular holders located in the ground ladder storage compartment area. L 3. There shall be one ( 1) 6 foot pike pole with fiberglass I beam handle provided. The pike pole shall be stored in tubular holders located in the ground ladder storage compartment area. Meets Exceeds Comments: M 0 r- a 201. PUMP U_ Pump shall be a minimum, 1500 gpm single stage midship mounted centrifugal type, mounted