READ ALONGSIDE THE SOURCE
Okaloosa County BOCC — March 4, 2014 — Repair & Paint Countryview & Bluewater Tanks — reading text
Part 39 of 40. These parts divide the reading text for browsing; they are not the source document's page numbers.
Machine-extracted text — 36-Repair _ Paint Countryview _ Bluewater Tanks.pdf
Machine-extracted OCR text · Review label: Machine produced / unreviewed
Compare this copy with the preserved source. Review labels describe the recorded status of this file; they do not guarantee that the text is error-free. Spacing and line breaks are retained, with long lines wrapped to fit the screen.
under any compressors, paint pumps, mixers,
welding machines, etc., to prevent oils, solvents, organic compounds, or other
contaminants from leaching into the soil. Any oils, solvents, organic compounds,
or contaminants spilled on the site during the process of the Work shall be
immediately removed and cleaned up by the CONTRACTOR
B The CONTRACTOR shall grade and level the site upon completion of all work and
Repair & Paint 009870 - 31
Countryview & Bluewater Tanks (2014) Job No. 41-459
grass the site with rye or other type grass that will provide cover to all disturbed
areas. This work shall be completed at no extra pay to the CONTRACTOR.
3.12 REPORTS
A. The CONTRACTOR shall complete the reports included at the end of this section for
this project. The report shall be completed daily and sent to the Owner and Engineer
for their review and records.
B. No progress payments will be authorized for payment until acceptable completed
reports are properly submitted.
3.13 PRODUCT PERFORMANCE CRITERIA
Provide the following product information and manufacturers published performance
data should coatings or coating system be submitted in lieu of the standard of quality
established in the project documents. Should the data not be available in a published
format, or if the duration of the test does not meet the specified requirement, please
respond in the appropriate space with NT (Not Tested).
A. Interior and Exterior Primer
1. Generic Type: Organic Zinc Rich Urethane Primer
2. Special Qualifications: Certified in accordance with ANSI/NSF STD 61 for
contact with potable water in tanks of 1,000 gallons
capacity or greater.
3. Solids By Volume: 63%
4. Zinc Content: 83% by weight
5. Test Criteria:
Test Criteria Test Duration Proposed Product Test Results
Rust @ Scribe:
ASTM B 117 50,000 hours Plane Rust:
Salt Spray (Fog) (Scribed Panel)
Blisters:
Rust @ Scribe:
ASTM G 85
15,000 Hours Plane Rust:
Prohesion Blisters:
ASTM D 4585 Rusting:
4,000 hours
Humidity Blistering:
Repair & Paint 009870 - 32
Countryview & Bluewater Tanks (2014) Job No. 41-459
ASTM 4541 Average of Three
Report PSI
Adhesion Tests
ASTM G8
Cathodic 30 Days Exposure
Disbondment
Immersion Service 7 years – No
(Potable Water) Failure
B. Exterior 1st Intermediate Coat
1. Generic Type: Polyamidoamine Epoxy
2. Solids By Volume: 67%
3. Special Qualifications: Certified in accordance with ANSI/NSF STD 61 for
contact with potable water in tanks of 1,000 gallons
capacity or greater.
4. Test Criteria:
Proposed Product Test
Test Criteria Test Duration
Results
Rust @ Scribe:
ASTM B 117 10,000 hours
Plane Rust:
Salt Spray (Fog) (Scribed Panel)
Blisters:
Rust @ Scribe:
ASTM G 85
5,000 Hours Plane Rust:
Prohesion
Blisters:
ASTM D 4585 Rusting:
10,000 hours
Humidity Blistering:
ASTM 4541 Average of Three
Report PSI
Adhesion Tests
CS-17 Wheel
ASTM D 4060 Report mg loss / Average of
1,000 Gram Load
Abrasion three tests
1,000 Cycles
Immersion Service Rusting:
2 Years
(Potable Water) Blistering
Repair & Paint 009870 - 33
Countryview & Bluewater Tanks (2014) Job No. 41-459
C. Exterior 2nd Intermediate Coat
1. Generic Type: Aliphatic Acrylic Urethane.
2. Solids By Volume: 71%
3. Test Criteria:
Test Criteria Test Duration Proposed Product Test Results
Rust @ Scribe:
ASTM B 117 9,000 hours Plane Rust:
Salt Spray (Fog) (Scribed Panel)
Blisters:
Rust @ Scribe:
ASTM G 85
10,000 Hours Plane Rust:
Prohesion Blisters:
ASTM D 4585 Rusting:
4,000 hours
Humidity Blistering:
ASTM 4541 Average of Three
Report PSI
Adhesion Tests
CS-17 Wheel
ASTM D 4060 Report mg loss / Average of
1,000 Gram Load
Abrasion three tests
1,000 Cycles
ASTM D 522 Method B
Flexibility Cylindrical Mandrel
ASTM D 4141,
Gloss Retention:
Method C 500 MJ/m2
Color Change:
(EMMAQUA)
ASTM D 2794
Direct Impact Report in/lbs:
Impact
Repair & Paint 009870 - 34
Countryview & Bluewater Tanks (2014) Job No. 41-459
D. Exterior Finish Coat
1. Generic Type: Fluoropolymer Urethane.
2. Solids By Volume: 60%
3. Test Criteria:
Test Criteria Test Duration Proposed Product Test Results
Rust @ Scribe:
ASTM B 117 10,000 hours Plane Rust:
Salt Spray (Fog) (Scribed Panel)
Blisters:
ASTM D 4585 Rusting:
3,000 hours
Humidity Blistering:
ASTM 4541 Average of Three
Report PSI
Adhesion Tests
CS-17 Wheel
ASTM D 4060 Report mg loss / Average of three
1,000 Gram Load
Abrasion tests
1,000 Cycles
ASTM D 522 Method A
Flexibility Cylindrical Mandrel
1,500 MJ/m2* Gloss Retention:
ASTM D 4141, UV Exposure Color Change:
Method C
(EMMAQUA) 3,500 MJ/m2* Gloss Retention:
UV Exposure Color Change:
ASTM D 2794
Direct Impact Report in/lbs:
Impact
% Gloss Retention:
ASTM D 4587 16,000 hours
Color Change:
QUV Exposure
Cycle 4: 8 hours UV -
% Gloss Retention:
4 hours condensation 25,000 hours
Color Change:
ASTM D 5031